Sliding & Patio Doors in Riviera Beach - Free In-Home Measure, Written Price

Trusted Sliding & Patio Doors for Riviera Beach Homeowners

Sliding and patio door replacement in Riviera Beach typically runs $1,800 to $6,400 installed, depending on the door system, glass package, and framing work involved. Most single-panel patio door replacements are completed in one day by a two-person crew. We’ve been doing this work across Palm Beach County since 2008, and we answer the phone at (786) 829-6722 every time you call.

Call (786) 829-6722

A sliding door that sticks in the track, lets daylight through the jamb, or fogs between the glass isn’t a small annoyance. It’s a door that has already failed. Riviera Beach houses take a beating from salt air, afternoon heat, and the occasional tropical storm band that rolls in off the Atlantic. Dale Kessler started TruePane Windows & Doors because he kept seeing the same problem across the county: homeowners paying twice for the same door, once for the cheap install and again for the fix. We do it right the first trip, and we put that in writing.

What Our Sliding & Patio Doors Service Includes

We install, replace, and service five categories of sliding and patio doors in Riviera Beach. Each one has different engineering demands, different framing tolerances, and different failure points. The crew that installs a header-hung panoramic slider isn’t the same skill set as the crew that rebuilds a pocket door pocket. We send the right people, and we measure twice before the first cut.

Patio Sliding Doors

These are the standard two- and three-panel sliders most Riviera Beach homes were built with, usually a six-foot or eight-foot opening. We replace rollers, rebuild tracks, reset jambs, and hang new doors when the old unit has gone too far. Most Patio Sliding Doors replacements in Riviera Beach take one day, and we register both warranty layers before we leave the driveway.

What matters with a patio slider is the square. A door that’s out of true by even a quarter inch will wear rollers unevenly and bind in August when the frame swells. Dale’s rule is on the whiteboard in the shop: if the pane is not true, the job is not done.

Panoramic Sliding Systems

Panoramic Sliding Systems mean large-format glass panels, usually three or more, that stack or disappear into a wall pocket to open a room to the lanai or pool deck. These are engineered systems with header loads measured in the thousands of pounds. We set the header, shim the track dead level, and hang each panel to factory specs.

In Singer Island and along the Intracoastal, we see these systems fail because the original install was rushed and the header settled. A 12-foot glass panel doesn’t forgive a rushed install. We take the time on the front end so the door operates smooth on day one and year twenty.

Heavy-Duty Sliding Doors

Heavy-Duty Sliding Doors handle oversized openings, impact-rated glass, and doors that see daily commercial-level cycling. These units need reinforced tracks, upgraded rollers, and framing that won’t flex under the weight. We quote impact-rated options from PGT and CGI as standard practice for Riviera Beach homeowners who want one door that does everything.

What separates a heavy-duty install from a standard one is the track bedding. We set the track on a continuous shim bed and anchor it at the manufacturer’s specified intervals, not where the old screw holes happened to be. That’s how you get a door that doesn’t sag in five years.

Pocket & Barn Doors

Pocket & Barn Doors slide into the wall cavity or ride on a surface-mounted rail, respectively. Both are popular in Riviera Beach ranch homes where floor space is tight and a swinging door wastes room. We work on existing pocket doors that have jumped the track, and we install new barn door hardware on reinforced headers.

The most common pocket door failure we see is a top-hung door where the framing above the pocket wasn’t reinforced at the time of construction. When we open the wall, we add the blocking and header support the door should have had from the start. Then we hang it level and test it twenty times before we pack up.

Screen Door Installation

Screen doors on sliding patios in Riviera Beach take direct sun and salt spray all year, which eats cheap aluminum frames and warps the mesh. We install replacement screen doors with corrosion-resistant frames and pet-resistant mesh options. A screen that fits square without daylight gaps keeps out no-see-ums, which in the summer months is a quality-of-life issue as much as a door issue.

We measure the opening, build or order the screen door to size, and adjust the closer so it doesn’t slam. A screen door that doesn’t shut square is a door that will warp within a season.

Brands We Service for Sliding & Patio Doors

We’re an authorized installer for Andersen sliding and patio doors, and we’ve hung enough of them across Palm Beach County to know their locking mechanisms and track profiles by feel. Andersen’s newer gliding units use a different roller carriage than the 1990s models, and swapping parts between generations is a real problem if you don’t know the difference. We stock OEM rollers, handles, and weatherstripping for Andersen units, so a repair doesn’t turn into a three-week wait for a small part.

We also install and service PGT sliding doors, which are the dominant impact-rated brand on Florida’s east coast for good reason. PGT’s engineering is meant to take a hurricane hit and stay sealed, but the install has to match the engineering. We follow PGT’s installation specs to the letter, including the anchor schedule and the perimeter sealant detail. Whether you have Marvin, Andersen, PGT, or any other make in your Riviera Beach home, we can quote the replacement or do the repair. Bring us the brand you have and we’ll show you the numbers side by side on paper.

For a deep look at how TruePane approaches every door and window we touch, start at our home page and see how The Keystone Standard applies to the whole scope of our work.

Signs You Need Sliding & Patio Doors Right Now

• The door jumps the track or derails. When a sliding door lifts off its lower track, the rollers are shot or the track is bent or packed with debris. Operating the door once it’s off the track can gouge the bottom rail and turn a $100 roller job into a $900 panel replacement. Stop using the door and call us.
• You can see daylight through the jamb, or the door rattles in wind. A sliding door that has visible gaps around the frame has failed weatherstripping or a settled opening. Riviera Beach afternoon storms pull sideways rain, and a gap that lets light through will let water through in a true squall. The fix is usually new seals and a jamb adjustment, not a full replacement.
• The glass is fogged between panes. Fogging means the insulated glass unit has lost its seal, and the desiccant inside the spacer has absorbed all the moisture it can hold. You cannot clean it off. The seal failure usually gets worse, and the only permanent fix is a new IGU. We handle IGU replacement on most major sliding door brands.
• The door grinds or sounds like it’s dragging gravel. That sound is a roller bearing that has disintegrated and is now grinding metal on metal inside the bottom track. Continued use scores the track, which means the track itself has to be replaced. Catch it early and it’s a simple roller swap.
• You have to lift the door or shoulder it to close it. A sliding door that needs muscle to operate has fallen out of alignment, the frame has settled, or the rollers have collapsed. Forcing it works the door every day out of square, which compounds the damage. The longer it runs like that, the more involved the repair gets.

Our Sliding & Patio Doors Process - Step by Step

We’ve built our process around a simple rule: you should know exactly what’s happening, exactly what it costs, and exactly when we’ll be done. Here’s how a typical sliding door job goes in Riviera Beach.

1. 1
   Call and talk to a person. You call (786) 829-6722 and a live person answers, 24 hours a day. We take down the issue, the door brand, the rough opening size if you know it, and the symptoms. No voicemail tree, no callback form. If it’s an emergency and you’re in Riviera Beach, we’ll tell you right there on the phone how soon we can be at your door.
2. 2
   On-site measurement and diagnosis. A uniformed, background-checked technician comes to your house and measures the opening twice. We check the level of the header, the condition of the subfloor under the track, and the square of the rough opening. For a sliding door, a 4-foot level on the track and a diagonal measurement of the opening tell us most of what we need to know about why the old door failed.
3. 3
   Written line-item quote. We put the numbers on paper, side by side across manufacturer lines if you’re comparing brands. You’ll see the door cost, the framing work, the haul-away of the old unit, and the installation labor as separate lines. The price we give you is the price on the bill. No change orders for work that should have been in the first quote, no surprise line items at the end.
4. 4
   Installation day. We arrive when we say we will, protect the work area, and set the door true. That means shimming the frame against the rough opening so the side jambs are plumb in both directions, the head is level, and the track is supported continuously. We seal the perimeter with the manufacturer-specified sealant, set the door panels, and cycle the door repeatedly until it rolls clean.
5. 5
   Registration and walkthrough. Before we leave, we register both warranty layers in writing, with durations stated. That’s The Keystone Standard, and it’s on every job. We walk you through how the door operates, what the lock does, and what normal maintenance looks like. Then we hand you the paperwork and leave the work area clean.

Riviera Beach homeowners dealing with window issues alongside their sliding doors can read more about our approach on our Sliding & Patio Doors in Juno Beach page, which covers the same standard of work just north of town.

How Much Does Sliding & Patio Doors Cost in Riviera Beach?

Sliding & Patio Doors Near Riviera Beach - Our Service Area

We serve Riviera Beach and the surrounding communities including Palm Beach Shores, North Palm Beach, Lake Park, Westgate, West Palm Beach, and Palm Beach Gardens. We also work north into Juno Beach and Jupiter and south into Palm Beach and Palm Springs. Typical scheduling in Riviera Beach is same-week for estimates, and urgent door repairs get priority when a door won’t close or won’t lock. Our Sliding & Patio Doors in Lake Park page covers the service area just south of downtown Riviera Beach, and we work across the whole northern Palm Beach County corridor.

Frequently Asked Questions - Sliding & Patio Doors in Riviera Beach

Schedule Your Sliding & Patio Doors Service in Riviera Beach Today

If your sliding door is fighting you, fogging up, or letting the outside in, call TruePane at (786) 829-6722. We’ll send a technician to measure, diagnose, and put real numbers on paper. The estimate is free, the warranty is in writing, and the work is done right the first time. Dale Kessler’s rule still stands: if the pane is not true, the job is not done.

Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Riviera Beach since 2008.