Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterPly Gem Door Installation: The Riviera Beach Owner’s Guide
Ply Gem door installation in Riviera Beach typically runs $340 to $890 installed, depending on whether we’re resetting an existing slab, replacing weatherstripping and hardware, or hanging a new prehung unit in an existing opening. We stock Ply Gem-compatible replacement parts on our trucks, and most door installation jobs are completed in a single visit. The call usually starts the same way: a door that worked fine for fifteen years suddenly drags against the frame in July, or the lock no longer lines up with the strike plate, or daylight shows under the weatherstrip. The frame has settled, the hinges have worn, or the original install was never square to begin with. If the pane is not true, the job is not done, and a door that is not true is just a slower version of the same problem.
Which Ply Gem Models This Applies To
Ply Gem has produced several door lines over the years, and they are not all interchangeable. The three we see most often in Riviera Beach are the Classic series (builder-grade hollow steel and fiberglass, common in homes from the late 1990s through the 2010s), the Pro series (upgraded fiberglass with better weatherstripping and adjustable thresholds), and the Premium series (wood-grain fiberglass and steel doors with heavier hinge hardware). We also work on the older Grand View sliding patio lines, though those share parts with the sliding door side of our shop.
The part that matters is not the door brand printed on the sticker. It is the measurement. A Ply Gem door is made to a rough opening that is typically 82 inches high by 32, 34, or 36 inches wide for a single front door, so a 36-by-80 replacement slab is not a generic 36-by-80 if rough opening and jamb depth are off. We measure the slab, the jamb, the hinge-to-hinge spacing, and the backset on the lockset before quoting anything. If a customer has a Ply Gem part number from the door’s edge sticker, that helps. But we have been burned by that sticker before: sometimes it is the lot number for the whole house, not the door itself. Dale Kessler’s rule on this one: if it is not right on paper, it will not be right on the wall.
On the parts side, we’ll install an OEM Ply Gem component when it is available and genuinely better, but we do not wait two weeks for a hinge pin if a quality aftermarket equivalent will outlast the original. That is particularly true for weatherstripping and threshold caps in Riviera Beach, where salt air from the Blue Heron Bridge area eats aluminum finishes faster than the rest of the county.
Signs Your Ply Gem Door Installation Is Failing
- The door scrapes the top or latch-side jamb in summer. Wood framing and even metal door slabs expand in Riviera Beach humidity. If the install did not account for seasonal movement, the slab binds. On metal doors, the paint and primer wear off along the top edge first, which is the tell.
- The deadbolt does not line up with the strike plate. This is usually hinge sag, not a lockset problem. The top hinge screws have pulled loose from the jamb, or the hinge knuckles themselves are worn. Fixing the lockset without fixing the hang is repeating the same repair every three months.
- Daylight is visible under the door or along the latch side. Weatherstripping compresses, threshold caps crack, and the sweep starts to fold. In Riviera Beach, a gap here also invites the insects and the humidity.
- The door closes by itself, or drifts open. The frame is out of plumb. This is a framing and shim problem, not a hinge adjustment. It usually means the original installer set the jamb with a level on only one side.
- The fiberglass skin or steel face is cracking where the hardware attaches. On Ply Gem builder-grade slabs, we see this after ten or fifteen years, especially when someone replaced the original handle with a heavier one and the door face was not reinforced. Once the skin is compromised, the door is done, even if it looks fine from ten feet away.
Replacement Cost & What’s Included
A Ply Gem door installation in Riviera Beach breaks down in a straight line: rehanging an existing slab with hinge and jamb correction runs $340 to $520; new weatherstripping and a threshold cap add $80 to $150; replacing the slab in the existing jamb runs $410 to $680 depending on fiberglass or steel and whether we’re reinforcing the hardware mounts; and a new prehung door, installed square and shimmed, runs $590 to $890. What drives the range is whether the existing jamb is solid enough to keep, whether the rough opening needs a closer, and whether there is any damage we cannot see until the trim is off.
Every quote includes the labor, the shims, the insulation around the jamb, the fastener work, and the warranty registration on the parts we install. That last point matters more than most people think. The Keystone Standard means both warranty layers are registered in writing before the truck leaves your driveway. You will not find a surprise line item on the bill for a shim pack or a tube of caulk. That is a square deal, and we do not run jobs any other way.
DIY or Call Us?
An owner can check a few things safely: whether the hinge screws are stripped, whether the weatherstripping is cracked or flattened, and whether the door is hanging level using a simple four-foot level. You can also clean the threshold track and confirm the sweep is not torn. None of those checks require pulling the door or touching anything under tension.
Where DIY goes wrong on a Ply Gem door is in the rehang. A door that drags in July and drafts in January needs the jamb re-shimmed, not just the hinges tightened. Pulling a door slab alone is where we see stripped screw holes, broken glass inserts, and someone getting pinned between a 70-pound slab and a wall. We have also fixed more than one install where the homeowner planed the door bottom and then could not get the weatherstrip to seal against a now-tapered gap. If you are not certain it is right, call us at (786) 829-6722 and let us put eyes on it before you take anything apart.
FAQs
A rehang or slab replacement is typically a three-to-four-hour job on site, and most are completed in a single visit. We schedule the day in advance, and the live person who answers the phone knows the actual schedule.
Yes, if the slab is sound, the jamb is intact, and the frame can be re-shimmed square. We will not pad a quote toward a new door when the existing one is salvageable. Call (786) 829-6722 for an honest read.
Our trucks carry Ply Gem-compatible weatherstripping, threshold caps, hinge sets along with parts for Andersen, and Pella, and a full shim and fastener kit. We also carry fiberglass and steel slabs in common Riviera Beach sizes, so one visit usually finishes the job.
In our coastal climate, a builder-grade Ply Gem door lasts ten to fifteen years before the weatherstrip and threshold need real attention. A well-installed Pro or Premium series door, with the jamb shimmed square and both warranty layers registered, often runs twenty or more.
Correcting a sagged hinge and re-shimming a binding jamb typically runs $340 to $520 in Riviera Beach. The price changes most when the jamb itself is compromised and needs reinforcement rather than a simple re-shim. Call (786) 829-6722 for a written quote.
If your Ply Gem door is dragging, drafty, or not latching, call TruePane Windows & Doors at (786) 829-6722. We will measure it twice, quote it on paper, and stand behind the work. Dale Kessler grew up in the Blue Heron neighborhood of Riviera Beach, and he still runs every job by the founding rule that named the company.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Riviera Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.