Mr-Glass Custom & Geometric Windows Nationwide | TruePane Windows & Doors

Mr-Glass Custom & Geometric Windows in Riviera Beach: What to Know First

TruePane Windows & Doors installs and services Mr-Glass custom and geometric windows in Riviera Beach as an independent Mr-Glass service provider. Most custom and geometric work runs $850 to $4,200 depending on the size, shape, and glass spec, and most jobs are completed in a single visit once the glass or sash arrives. We are not affiliated with Mr-Glass, which matters because we answer only to you, not to a manufacturer’s cost-cutting playbook.

Call (786) 829-6722

This page is for homeowners in Riviera Beach who own a Mr-Glass window, usually a shaped or oversized unit, and need it measured, repaired, reglazed, or replaced correctly. If that sounds like you, call (786) 829-6722 and you will get a live person, not a recording.

How Mr-Glass Products Fail - and How We Fix Them

Mr-Glass builds a solid window, but every window line has its weak points. In Riviera Beach, the salt air and afternoon thunderstorms find those points faster than most climates do. Here is what we actually see on service calls:

• Arched and radius units with a failing top seal. On Mr-Glass geometric shapes, the curved glass-to-frame bond at the apex is the first place moisture finds its way in. You will see condensation inside the curve, often months before the glass fogs fully. We remove the sash, dry the channel, and rebed the unit with a marine-grade sealant that holds up to the salt spray off the inlet.
• Triangles and trapezoids that were never properly shimmed. A shaped window carries its weight unevenly, and if the original installer shimmed it like a rectangle, the glass eventually binds against the frame and cracks at the corner. We reset these on tapered composite shims and re-square the rough opening before the new unit goes in, which is the step most rushed installs skip.
• Oversized fixed trapezoids with sagging mullions. On Mr-Glass picture windows over eight feet wide, the center mullion can deflect over time, especially after a hard hurricane season. You will notice the frame pulling away from the wall at the midpoint. We reinforce the mullion and refit the glass rather than just caulking the gap and hoping for the best.
• Custom octagon and circle windows with failed perimeter gaskets. Mr-Glass shipped some of its geometric units with butyl tape that degrades faster in Riviera Beach’s heat than it does inland. The result is a draft you can feel around the glass on a windy day. We strip the old tape and replace it with an EPDM gasket that does not dry out the same way.
• Clad geometric frames with corrosion at the corner keys. On coastal Mr-Glass installs, the aluminum corner connectors inside the frame can corrode where salt air and condensation collect. You may see a white powder or a hairline crack at the corner. We disassemble the frame, clean or replace the keys, and reassemble with a corrosion inhibitor so the fix outlasts the original.

Our Mr-Glass Custom & Geometric Windows Process

Every Mr-Glass job in Riviera Beach follows the same order of work. No shortcuts, no surprises.

1. 1
   Call and diagnosis. You call (786) 829-6722. A live person answers. We ask for the window’s location, size, and what you are seeing, then set a time to come look at it.
2. 2
   Measurement and inspection. A background-checked, uniformed technician shows up, measures every opening twice, and checks the frame, the glazing, and the surrounding wall for water intrusion and settlement.
3. 3
   Parts decision on paper. We quote OEM and quality aftermarket options side by side, in writing, with delivery timelines and warranty coverage stated plainly. You decide, with full information.
4. 4
   The repair or replacement. We install, reglaze, or reset the unit, shimming shaped glass properly and sealing every joint with materials rated for coastal Florida.
5. 5
   Testing. We check for drafts, binding, and proper drainage, and run a water test on the exterior to confirm the seal holds.
6. 6
   Warranty registration before we leave. Both manufacturer warranty layers are registered in writing, with durations stated, before the truck leaves your driveway. That is The Keystone Standard.

What Mr-Glass Custom & Geometric Windows Costs in Riviera Beach

Here is what we quote on most Mr-Glass work in Riviera Beach, depending on the unit’s size, shape, glass type, and condition:

The price depends on glass spec, whether we rebuild the rough opening, and how long the custom unit takes to fabricate. You will get a written line-item quote before any work begins, and the price on that paper is the price you pay. Call (786) 829-6722 for a free estimate.

Why Riviera Beach Homeowners Call TruePane Windows & Doors for Mr-Glass Work

We work on more than a dozen manufacturer lines besides Mr-Glass, including PGT, CGI, CWS, and ES Windows. That matters because a technician who sees only one brand develops blind spots. We see how different manufacturers solve the same coastal problems, and we bring that knowledge to every Mr-Glass job.

Dale Kessler grew up in the Blue Heron neighborhood of Riviera Beach and has spent the better part of two decades measuring, setting, and weatherstripping windows and doors across Palm Beach County. Our work is covered by the Done Right Promise: if it is not done right, we make it right, with no paperwork or arguments. A live person answers our phone 24 hours a day, seven days a week. If the pane is not true, the job is not done.

FAQs